Drawings or pictures may show non-standard equipment.

BOLLARD™ 65kW Marine Generator

The BOLLARD™ MGP65 will carry the load over the long haul.

Over 55 years of design experience and excellence has produced this model featuring an industry leading 4.5 liter turbocharged engine.

Matched to a high-efficiency motor starting generator and built to be a BOLLARD™, there is no other machine at this power rating which can match in reliability, durability, and provide the lowest operating cost. Add on the SeaDrive™ option to drive your hydraulics.

Count on BOLLARD™ to pull harder.

EPA certified Tier 3 Marine, CARB, EU & MOC


Unsurpassed Quality & Reliability
BOLLARD™ Generators are designed and built in the USA specifically for the rugged conditions of commercial use. The expected time between overhauls on the BOLLARD™ packaged generator set is 40 to 50 thousand hours.

High-Efficiency Motor Starting
Heavy Duty windings engineered for 80°C rise of 40°C ambient yield extended insulation service life, high electrical efficiency for maximum fuel economy, and superior motor starting at all voltages. PMG dedicated excitation is standard, resulting in even higher motor starting together with 300% sustained short circuit capacity along with VFD and paralleling compatibility.

The BOLLARD™ MGP50 –MGP395 Gensets are EPA certified Tier 3 Marine, CARB, EU, and MOC. They meet the lowest emissions levels available on the market today without exhaust after-treatment resulting in reduced maintenance and operating costs while preserving our clean air and water quality.

Keel Cooling, Heat Exchange, or Radiator Compatibility
Premium Marine Grade ProtectionBollard generators feature Imron™ 2 part marine epoxy overcoats on the engine, generator, and base frame. Accessory brackets are typically powder coated, and fasteners are primarily stainless steel to protect your investment from the harsh marine environment.

Heavy Duty Structural Steel Base Frame & Reduced Noise
For ease of installation, added structural integrity, safety and durability. Superior vibration and noise dampening with a high mass flywheel, polyurethane vibration isolators, mass loaded & stiffened base frame, and de-noised engine.

Heavy Duty Air Intake Filtration & Silencing
For increased performance, extended engine life, and quiet operation

Controls, Gauges, & Instrumentation
Standard enclosed prewired J1939 digital control panel with key start/stop and run/idle switch. Safety shutdowns are programmed for high water temp, low oil pressure, and over-speed. Included are LED readout of all J1939 trouble codes and diagnostics. Custom panels offer, auto-start/stop function for inverter or paralleling interface, load sharing, digital generator output LEDs and full function electrical distribution switchboards.

Optional SEADRIVE™ Front Power Take Off System
Compact heavy duty housing, pre-aligned, easy to install, service friendly, integrated torsional coupling, and available with or without a clutch.

Optional SCOR™ Sea Change Oil Regeneration System
1µ bypass oil filter. Safely extends oil drain intervals and engine life

Download the brochure


Engine Model 4045TFM85
Engine Type In-Line | 4 Cycle | 4 Cylinder | Diesel
Displacement – L (cu.in) 4.5 (275)
Bore x Stroke – mm (in) 106 (4.17) x 127 (5.00)
Aspiration Turbocharged
Oil Sump Capacity – qts (L) 19 (18)
Emission Regulation EPA Commercial Marine Tier 3
Prime – 60hz, 1800RPM (HP) 65 kW (87)
Standby – 60hz, 1800RPM(HP) 71.5 kW (96)
Motor Starting Range – HP 23.5 – 65 (Code G Motor @ 208VAC)
Voltage Regulation +/-25%
Starter 12v | 4.5kW
Alternator 12v | 75 Amp
Operating Angle – Degrees 20 (Constant) | 30 (Intermittent)
Dry Weight – lbs 2028 (engine, 362 gen, skid)
Length x Width x Height – in (See brochure for details)