Drawings or pictures may show non-standard equipment.

BOLLARD™ 210kW Marine Generator

SKU: MGP210 Category: Tags: ,

BOLLARD™ Generators are designed and built in the USA specifically for the rugged conditions of commercial marine use.

The expected time between overhauls on the BOLLARD™ packaged generator set is 20 to 50 thousand hours.

Built with John Deere 6090AFM85 marine engines.

EPA certified Tier 3 Marine, CARB, EU & MOC

Description

Standard Equipment

  • John Deere 1800 RPM, EPA/CARB certified Tier 3 marine diesel engines
  • Marathon motor start generator rated 80C/40C for maximum electrical efficiency
  • Dedicated PMG excitation with 300% short circuit protection and VFD compatibility
  • Digital parallelable automatic voltage regulator – .25% voltage regulation no load to full load
  • Remote start digital control panel with J1939 diagnostics and 3′ extension harness
  • Automatic safety shutdowns for low oil pressure, high water temp and over speed
  • Structural steel welded base frame with vertical and horizontal gusset supports
  • Coast Guard approved JIC fuel supply and return line fittings installed
  • Isoflex™ anti-vibration mounts between engine/generator and base frame
  • Closed crankcase engine ventilation filter system
  • Dry element cleanable combination air intake filter/intake silencer
  • Dry exhaust elbow with mating flange, high temperature gasket and stainless hardware
  • Coolant recovery bottle
  • Starter and alternator 12V std on 40kW-150kW, 24V std 200kW-385kW
  • Imron™ two-part epoxy marine paint for maximum corrosion protection
  • Stainless steel fasteners and powder coated accessory brackets
  • All generators are calibrated, and load tested under full load before shipment
  • Single phase 4 wire generators are oversized to allow full load single phase output 105/40c @ 1.0PF
  • Three phase generators are 12 lead reconnectable voltage, 50Hz or 60HZ
  • Heat exchanger cooled engines include bronze gear driven raw water pumps and Cu/Ni HE cores
  • Stainless steel water injected exhaust elbows are Included with HE cooled engines

Download the Spec Sheet

Engine
Single Circuit Keel Cooling Package
Single Circuit Heat Exchange Package
Single Circuit Marine Radiator Package

Motor Starting Upgrade Options
(Code G Motor @ 208VAC)
Up to 1:1 HP per kW

Air Intake & Filtration
K&N Air Filters
Donaldson Air Silencer
Closed Crank Case Vent Loop

Controls & Instrumentation
Control Panel
Custom Harness Length
Auxiliary Start Panel
Auto Start/Stop
Pre-Alarm Senders
AC Meter Panel
Low Coolant Level Shutdown
High Water Temp. Shutdown
Low Oil Pressure Shutdown
Low Oil Level Gauge/Shutdown
Overspeed Shutdown
Paralleling & Load Share
Over-Voltage Alarm
Over-Current Alarm
Under-Current Alarm

DC Electrical System
Battery: 12v | 24v
Battery Rack & Cables
Battery Isolation Switch

Fuel-Lube Oil System
SCOR™ Oil Regeneration System
Oil Drain Extension W/ Valve
Oil Drain Pump to Engine
Move Dipstick To Opposite Side
High/Low Oil Level Shut Down
Custom Oil Drain Hose Length
Single Side Service
Lube Oil Drip Pan

Exhaust
SS Wet Exhaust Mixing Elbow
Dry Exhaust Matching Flange
SUPERFLEX™ Exhaust Bellows
Cowl & EM Exhaust Silencers
Heat Recovery Silencer

Power Take Off
SEADRIVE™ Clutched Front PTO
Clutch: Air | Oil | Electric
SEADRIVE™ Direct Drive Front PTO
Aux. A/B 2 Sheave Universal Pulley
Aux. A/B 4 Sheave Universal Pulley
Additional Belts

Additional Options
Sea Trial Start-Up
MER Site Start-Up w/ Load Bank
Custom Frame / Skid
Dual Vibration Isolation Mounts
Custom Sound Enclosure
Galvanized or Powder Coated Skids & Accessories
Racor Fuel Water Separator